5 steps to fix your water damaged phone

 3,989 total views,  1 views today

Hello friends, in this blog we will learn how to repair a smart phone if it falls into water. Many types of problems occur after falling into the water. Like many SMART PHONES keep going even after falling into water.

Some SMART PHONES become DEAD as soon as they fall into the water. In some SMART PHONES, charging issue occurs. Some SMART PHONES start heating up. We will know the solution of all these problems in this blog. After reading this blog, whatever kind of problem comes in the WATER DAMAGE PROBLEM, you will be able to fix that PROBLEM.

When someone’s smart phone falls into the water, they dry their phone in the sun or some PERSON put their phone in rice (RICE) for 1 day. It is successful 5% out of SOLUTION-100. To some extent, the water dries up but there are some places inside the mobile that the water in the gene does not dry up and it will damage the phone.

If your phone has fallen into water, then the machine to dry the water:

When you dry the phone in the sun, the phone will run once. But after some time, the problem will come in that phone and that problem will not be normal. Later, when you get his SOLUTION done, then it will cost more. . So if your phone ever falls in water, drying the phone in sunlight is 50% right. But after drying in the sun, once you go to a mechanic, you should get your phone fully cleaned and cleaned thoroughly. This brings PHONE back to the NORMAL CONDITION. This is for ADVICE CUSTMERS. Not for shopkeepers. The shopkeeper already knows these FACTS, but CUSTMERS does not know.

Now let me teach you how to make SOLUTION in any condition if a SMART PHONE falls in water –

If any SMART PHONE or any PHONE is still running after falling into the water. So how would you repair that phone in that CONDITION. To repair the phone, first of all you have to put the phone on the HEATING machine for some time, so that its DISPLAY will become hot and the water will be dried from the DISPLAY. After placing the phone on the HEATING machine for two to four minutes, open your phone. REMOVE the battery connector after opening.

After separating BATTERY all CONNECTORS will have to be removed. After removing CONNECTONS the motherboard has to be taken out. After removing the motherboard, the motherboard is to clean all parts with brush and petrol. Before CLEAN, the mother board has to SAFE the AREA containing the camera, sensor and mic. The camera has to be taken out and taped over the mic.

The motherboard has to be thoroughly cleaned with petrol. The section which has more water has to be photographed so that if any major issue comes on the phone after cleaning, then the solution of that section problem can be removed. After cleaning the motherboard, the camera jack has to be cleaned thoroughly with a brush. After cleaning the motherboard, one has to check each component and section thoroughly by placing the motherboard under the microscope.

If there is water in a section, then it has to be cleaned again. The shield will be placed above the IC with the help of TWIZER or s.m.d. After the unloading, around the IC after unloading, clean the petrol thoroughly and the hot GUN that is used for lamination in the last, let the hot air over the motherboard allow the motherboard to cool down after applying the air. is. After 5 to 10 minutes the motherboard has to be checked with multimeter whether it has SHORTING or not.

If there is no SHORTING in the phone, now we will connect the mother board, display and battery. This will keep the phone running in the right condition again. HOW TO CHECK SHORTING INSIDE THE MOTHERBOARD To check SHORTING, first of all set the multimeter to CONTINUITY mode, after setting the plus wire to ground. And attach the -VE wire to the plus point of the battery connector. To do.

If the value is coming from 300 to 500 then there is no SHORTING and if the value is approaching 800 900 then the phone is short. Now we have to attach the plus wire to the plus point of the battery connector and attach the minus wire to the motherboard ground. The value should be zero in this condition. SHORTING does not occur if the value is zero if the wire is straight and the value is 300 to 400 when it is vomited.

This CONDITION is not your mother board SHORT. The motherboard is not damaged by water. If this value is coming on both sides, then SHORTING has come on the motherboard. Then even if the phone is running in this condition, then it will go bad in some time or it will start heating up and the battery backup will be reduced. SHORTING has to be removed in this CONDITION.

If there is no SHORTING in the phone, then the mother board has to be attached to the display and battery and try again. This will keep the phone running in the right condition again, how to check SHORTING inside the motherboard. The first thing to do to check SHORTING is to set the multimeter to Continuity mode. After setting the plus wire is to be grounded and attaching the -VE wire to the plus point of the battery connector.

If there is too much water in the charging section, then the charging jack has to be cleaned first. Then try to change the charging jack. Because the charging jack is spoiled by water, if you clean the old charging jack then the problem may come in the future. Clean the motherboard properly but change the charging jack

If the display connector has water on it, how to fix it. If the phone is running after falling into water, but there is a problem with the display running, then to fix this PROBLEM the first thing is to clean the display CONNECTOR thoroughly. THINNER is not to be used here at all. Only use petrol or FELCON. After cleaning the connector with petrol,

The paste is to be applied on the display connector, after applying the paste all JECK has to be resold again with the help of iron. Similarly, a connector is also placed on top of the display and it has to be cleaned and resold again. DISPLAY after connecting is to connect. The problem of the display will be removed.

If the phone becomes DEAD after falling into the water, then how to fix it. :

To fix a DEAD phone, first of all we have to open the phone. The whole phone has to be cleaned after opening. After CLEAN, check with the multimeter whether the phone is full SHORT or HALF SHORT. If the battery connector gives a beep sound on plus and minus, then the phone will be full SHORT and if the value comes on both sides it will be half SHORT.

Full SHORT and Half SHORT have different SOLUTION. We will learn about both SOLUTION in this blog. OK

If the phone is full SHORT, then to solve it, first of all we need to check the capacitor in parallel. If there is water on any capacitor, then the capacitor has to be removed and SHORTING CHECK. If SHORTING does not come out then the capacitor has to be replaced. Iron the capacitor or s.m.d. Can be removed from If the SHORTING is not removed by removing the capacitor, then the IC around which the water will be more, will have to be checked. .

Remove the IC and check SHORTING. If SHORTING is exited on this exit, then that IC has to be reapplied by first REBOLL tax. Water falls under the IC due to falling in the water, most ICs run after REBALL. If you do not know how to make IC REBALL, then I will give the link below by reading it, you can learn IC REBALLING.

मोबाइल फोन में IC reballing कैसे करी जाती है ?

How do we know which component or which IC is SHORT? :

This TOPIC is very important to learn it carefully. In this, I will teach you that if the motherboard is SHORT, then how do you know which component or which IC is SHORT because if you see each component or IC from the motherboard up and down, then in this way your whole day only Waste and you will not be able to repair it even after finding out.

Because many times we see all ICs fluctuating but only one component is short. In this CONDITION you have to re-install the IC again by REBALL and REBALL cannot happen many times. The phone gets damaged. Therefore, you should take the same component or the same IC which has the problem because when the phone is SHORT then all the components which are in parallel become short. In this condition, we cannot know which component or IC SHORT is actually.

To find out which component or which IC is SHORT, for this we need SHORT KILLER. From SHORT KILLER we can EASLY find out which IC or component SHORT is. The SHORT KILLER ampere has to be set to 20 amperes to be detected from SHORT KILLER.

And set the voltage to 3 volts. That makes 20 * 3 = 60 WATT. Which is enough to heat any component or IC. After setting the voltage and ampere, the short killer plus and minus have to be attached to the plus and minus of the battery connector. Do not keep it attached for long.

When you attach the short killer key plus and minus wire to the plus and minus of the battery connector. Then the current of the ampere will go directly into the component which will be shot and will go into the ground. The component that is short will burn. Water will run out. By which SHORTING will be removed and by chance if any IC is short then that IC will become hot.

When hot, you have to remove that IC and try to REBALL first. If REBALL goes on then it is fine otherwise the IC will have to be changed. In this way we can remove half SHORTING or full SHORTING in any motherboard. EASLY is available in the short killer market. If you want to buy short killers, then I give you the link below. You can buy SHORT KILLER by clicking BUY NOW.

The short killer machine is an expensive machine that costs between 5 and 6000. If many mechanics are unable to buy this machine, then I have thought SOLUTION for that, which I will share with you, after understanding that even if you cannot take a short killer, you can remove the SHORTING of the motherboard, short killer your There is a good machine in place, but even if there is not a short killer, we can remove the SHORTING of the motherboard.

To make a short killer, we need two batteries. The ampere is written on both the batteries, assume the ampere is written 5AMP, meaning there is a battery of 5 amperes, the voltage on both is written 3 VOLT, then the circuit of both the batteries has to be removed and the plus of both is interconnected. Is and the two -ve have to be interlinked. After connecting it will give only 3 VOLT to both the battery output and the ampere will be connected to both, becoming 3 + 3 = 6AMP. 6 * 3 = 18 WATT.

In this way, you can make a short killer of 18 WATT, if you want to make a short killer with more power than this, then you can add another battery, in this way you can remove the SHORTING of the mother board. One plus is to take the WIRE and one -VE wire is to be attached to this wire at the plus and minus of the battery connector

Also the component or IC will know which component or IC is SHORT. Now we have learned almost all the ways that if a phone comes to us from cleaning to half shorting and half shorting to full shorting then how can we fix that phone.