Can we make Mobile Phone Battery by Ourselves

 2,558 total views,  2 views today

Look friends, learning to make mobile phone battery is also a part of mobile repairing course because suppose a customer comes to you, what is normal to take a mobile phone battery, which is a company phone, their battery is easily available in the market. But there are some phones whose battery is not available in the market or the Indian battery does not match in those that have come from outside.

So in this condition, if you know how to make batteries, then you can earn money from this talent, if it does not come, then you will drive the customer back. That’s why I will teach you how to make the battery of any phone, in different conditions, the battery is made in different ways, I will share with you all the methods, if you want to learn, then this blog is given full attention. have to study from and practice later

First of all, if you get a tab, then to make its battery, you will have to find the same size of the battery of the tab in the market, only you have to see the size and there is no need to see anything which will be the maximum size, you have to bring , after bringing the battery, the circuit that is installed on the battery

To remove it, first of all there is a tape on the circuit above the battery, you have to take off that paper comfortably as the tape comes off, the circuit is folded and you have raised that circuit straight have to do

After the circuit is straightened, the cells of the battery are connected with that circuit from 2 points below it, if you have to use that circuit in future then you have to remove the shoulder, with the help of iron, that point with a hot big iron. You have to separate them by applying paste, when those two points are separated from the circuit, then you have to type on both of those points, the wire does not stick easily on the points of the battery, you have to scratch a little with the surgical blade.

Paste has to be applied on it, after that if you stick the shoulder on it, it will stick a little. After you have to put both the wires on the plus and minus of the battery, now many brothers do not know how to check with a multimeter, then I also teach you how to check the plus minus

To check plus minus, you have to first set the multimeter to 20 volt dc, after setting it to 20 volt dc, the value of zero will come there, after that you have to put both the wires of the multimeter on both terminals of the battery. After putting it on the terminal of the battery, there you will find the voltage of the battery

That voltage should be three to four or five boards with voltage you will either see a sign of – or you will not see anything – it means that you have put the stars upside down on plus and minus plus has been placed.

And if no mark is coming then it would mean that you have put the stars straight where the plus is placed, it is the plus sign and where – it is the minus point of the multimeter, then you have found out from the market. After finding out which is the plus and which is the minus on the battery, you have to find both the wires, then after finding, you have to check on the battery connector as well that which is the plus –

Which is the first thing above the battery connector, then plus and minus are written, even if it is not written, then you have to check through multimeter which is plus and which is minus, now many brothers will not even know that I also teach you how to check plus and minus on the battery connector

To know the plus and minus on the battery connector, first of all, we have to set the multimeter on continuity mode and by attaching both the wires of the multimeter, check whether the sound of beep is coming or not if the sound of beep is coming. multimeter is working

So after this we have to attach the plus wire of the multimeter to ground and the minus wire to the point of one corner of the battery connector i.e. on the first or last one, at this point you will get a value close to 300 500 that plus sign And on which the minus point of the battery connector is to be touched on x/, then what is ours will run, most of the things that happen, they go straight after you come, you have to check two things.

First you have to check whether the type is turning on properly, after that you have to charge the tab, if the charging voltage is increasing or the charging percentage has started increasing, then the battery is fine, you can change the battery in this way. Are

If suppose the voltage is not increasing, then you will also have to install the circuit of that battery, now how will the circuit be installed, to install the circuit, which will be installed on the old battery, that circuit will have to be attached with the new battery, Then the connector of that circuit has to be connected with that connector, now how to connect the circuit, make a mark of plus and minus on the simple circuit also.

To touch the battery connector that will be made in the last, you have to attach that connector on the motherboard and after that you have to check the charging, if it goes, then your battery is ready, what happens is that 90% of the battery’s cell If only they are bad, then in this condition we can only change the cell, the performance of the battery will be fine and backup also if suppose the voltage is not increasing,

So then you will also have to install the circuit of that battery, now how will the circuit be installed, to install the circuit, which will be installed on the old battery, that circuit will have to be attached with the new battery, then the connector of that circuit will be connected to that connector. Will have to connect together, now how to connect the circuit, make a mark of plus and minus on the simple circuit too.

To touch the battery connector that will be made in the last, you have to attach that connector on the motherboard and after that you have to check the charging, if it goes, then your battery is ready, what happens is that 90% of the battery’s cell If they are bad, then in this condition we can only change the battery, the performance of the battery will be fine and look at the backup too, so now we have learned to change the battery in every condition.

Now we will talk that if you come to an android phone, its battery is not available in the market, then how will you make its battery. learning how to learn

Now let’s talk about how to make an Android phone battery. To make an Android phone’s battery, first of all, we have to separate the circuit of the old battery. Before separating the circuit, you have to take full care of plus minus. Which is a plus and no one –

After that, you have to find the same size battery, the size may be a little smaller or bigger, there is no problem (after that you have to take care of its plus minus and not the battery which we have to change) Remove its circuit. Dena and connect the circuit of the old battery with the cell of the battery, the way to connect is to keep the same beans as we learned in the above tab

Just have to keep in mind that the plus of this cell is to connect with the circuit and the minus is to connect with the battery, after that the connector of the battery has to be connected with the motherboard, your battery will run.

I hope that you have learned how to make all types of batteries, now if you have a phone from any company, first you have to try to get the battery from the market, if it is not available, then you can buy any phone in this way. Battery can be made very easily and you can earn money in it, whatever problem you may face.

This, if the terminals of the battery are connected with any point, then there can be a fire in the battery, so when you have to make the battery, after making the battery, seal it with golden tape so that the battery is not connected to each other. And what you will use should also be of good quality, it is not such that you should not use jumper wire here on its own, if you are using jumper, then you have to use it by contact and should be thick.

Should not be thin, if it is thin, it will burn very quickly when we charge the phone, then at that time this wire becomes hot, if you use thin wire, it will burn very quickly and there are chances of battery shutting down. Or the phone can even restart, so you have to do this work with good quality, only then this formula is successful.